Відео

I did run a 1991 model MB 190E 2L for 2 years on E40 and it would not pass emmissions tests without it. But I did adjust the air fuel sensor (mechanically) to make it run a little rich, but it was already running rich before that. I tried 100% E85 and it was hard to start and had 0 torque (would not move at all without stopping) when the engine was cold, after 10 minutes you could could start driving and it did run ok but had lot less power then normal at low rpm, at higher rpm it felt like it had maybe more power. I tried 30% E85 in my Yamaha WR450f, it dissolved some plastic parts after 30 min in the carburetor and all the fuel emptied out on the tarmac ...

Can I leave it without any pipes? Just take off the muffler and call it a day or do I need the pipes?

My fully built all motor d16z6 in a stripped eg dx hatchback runs 12.9, in 1/4 mile

Thats absolutely horrible lol i hsve the same build in a eg hatchback tuned on bindata i just have bigger 240cc injectors and in vegas i ran a 14.6 1/4 time with a stsge 2 ckutch and 9lb flywheel..

Thumb down on this vedio for language and unprofessionalizm. Looks like a nice shop but the group of guys I would feel filthy getting back into my car after. I would call a priest to cleanse my car from all the evil spirits that surrounded it while work was done.

Hey Sir! We sincerely look for a video collaboration with you! Are you interested in trying our seat covers?

What state you located? Or where is your shop?

Noticed the set screw is not aligned with the flat side of the motor spindle. i dont know if its important but saw it that way on another video and seemd to make sense!

What happens if non of the lifters are loose and still all tight when you remove valve cover??? Does it mean it's not a lifter?

Those wheels are fire! 🔥

crispy

Sounds like a squealing pully 😂

The level of creativity and innovation in this conversation is truly inspiring. It's like witnessing the birth of new ideas.😛

My d16z6 stage one bloc cam cold air intake eBay intake manifold with a eBay 70mm TB stage 2 clutch eBay header not car to a 2.5 exhaust 450cc injectors walbro 255 tuned on hondata and in Vegas I ran 13.9 on r888 on the front

I have a 2014 gmc 2500 6.0 with the LS3 823 heads & 6L90E transmission & 411 gears just got the truck Norris cam with matching LS6 springs I am hoping that it will be as good as it did for you? Also I am getting the HP tuner and lap top so I can play with it tunning it myself so I hope it goes well for me

So good. Thanks man. Love your videos

Thanks! I’ll be using this video to do mine

I was thinking it was "Marty's Law" at work again...but it's not just me.Great video Buddy,have a DANDY summer.

Which tuner would I need if I install a Chopacabra cam on a bone stock 5.3L if at all? I’m also planning to leave the stock exhaust. Work truck no AFM from factory.

I’m done with jeep. Total garbage quality. None of the other vehicles I’ve owned in my lifetime required as much maintenance and repairs as my JK.

how much did this all cost?

Oh my lord- can you come fix mine in my Chevy truck?! 😅 they told me to get a replacement engine after just hearing it was a lifter issue. 😭

Hell yeah thanks

we all subie owners?

Did you do a PVC delete? The other end of the valve hose you took off where did it go

Thanks you're videos are excellent

How much does a job like this cost to get a trucked cammed?

what did you do to fit the lower part of the injectors ??

Wow-oh-Wow. I'll be darnd if your arn't a stud. Just did it and BAM works like a charm. I lost my battery and all kinds of crazy stuff happend and all rest except for that. I have the 2015 LS 460 F. So happy.

Hey man, Im assuming its still using the 6 speed zf? Whats your current diff ratio, and how do you like the acceleration? Have you had it cruising in the highway, and if so, did you like it? Thanks man! Sick build!

Another tip ypu can do to fo pulley installation for a stock or a front pinned dampner. Place the dampner in the sun for a couple hours to heat up a little, then spray the crank snout with a can of air duster upside down to freeze it and the pulley/dampner will virtually slide on.

Man if you throw in a 3200 stall you will not see any drop between gears. Sound good

Blown away such a good video on wet sanding and buffing

I have the same problem with my 2023 GX with only 1500 miles on it. I have noticed the lean from the first day when I took the delivery of the vehicle. The dealership has replaced the LEFT spring but now the driver side is about 3/4” to 1” taller than the passenger side. Is it normal ? What is the allowance difference between the sides?

Will this work in a 2015 Lexus suv? My sister bought a used one and there are NO lines when she uses her back up camera. Any suggestions on how to add lines or shots that year not have them?

What year is your civic?

My 96 LX sedan has a similar Grill how did you get that specific Grill from? the link if you don't mind

This car is nice .more videos on this car

Did the check engine light illuminate?

I need the numbers to torque down my head on my V6 4.3

How about the heated & cooled seats. Were you able to still feel them?

Can I do this with my 2019 Honda civic si

These techs having to deal with these kids and their phones shoved in their faces...

OMG ....That looked so bloody uncomfortable. Would have been nice to see a before and after 0 to 60. As well as some mpg

I’ve just been pushing my gas pedal down while starting the vehicle in the morning till I build oil pressure.🤷🏼‍♂️

The thing about trucks is that they are not the fastest, but THEY'RE SO FUN GETTING THERE!

Boost gauge with no turbo?

This is the best video ive seen on this! I cant believe the views and subs are so low! How long did this repair take you? You made it seem kinda painless.

My 2017 3.5 work truck has 273,000 miles and it’s never rattled or needed turbo work. Oil changes every 3,000 miles since new and always allowed to warm until the temp gauge moves before driving, as well as cool off for 30 seconds before shutdown when towing.

Hey bro I’m about to pick up an 01 here in a few days and I appreciate this video this has me hyped